HAPPYMODEL Mobula7 1S HD 75mm ブラシレス タイニードローン ELRS受信機 (support Gyroflow)

HAPPYMODEL Mobula7 1S HD 75mm ブラシレスドローン ELRS受信機 (support Gyroflow)
100g未満 ドローン完成機
X12 5-IN-1 AIO フライトコントローラー
VTX パワー最大 400mw
新しい RS0802 KV20000 モーター
1080P HD ビデオ録画
Blackbox Ready サポート GYROFLOW
1S Lipo/LIHVに対応
推奨 1S 450mah/550mah/650mah バッテリー (含まれていません)

ブランド名: ハッピーモデル
アイテム名: Mobula7 1S HD 75mm マイクロ FPV フープ ドローン
重量: 33g

Mode: RS0802 KV20000
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ10.5mm*13.5mm
No.of Cells(Lipo):1S only

Pitch:1 inch
Props Dia:40mm
Center Thickness:5mm
Center Hole Dia:1.5mm

Flight controller:
X12 ELRS V2.1 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
X12 Frsky V1.0/V2.1 flight controller built-in SPI FRSKY 2.4G receiver Target: CRAZYBEEF4FR
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689 or BMI270(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16
Built-in voltage detection
Built-in current sensor

Onboard 4in1 ESC:
Power supply: 1S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware
When use Blujay firmware with 48khz, should set startup power to 1100/1200

Onboard 5.8g OPENVTX:
Firmware version: OPENVTX
Smartaudio v2.1
PIT Mode support
RCE Mode support
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)

Runcam Split3-Lite:
Model: RunCam Split3-Lite
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V

External Blackbox and voltage booster module:
With Built-in Voltage booster module
SD Card support max to 32GB
SD Card need to use FAT32 Format
Notes: Need to careful to insert the TF SD Card , and don’t pull it out while install the battery.

1x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame) ELRS SPI receiver
1xExternal Blackbox Module support gyroflow
4xRS0802 KV20000 brushless motor
1xGemfan 1610-2 bi-blade propellers(4cw+4ccw)
1xRuncam Split3-Lite Camera+1080P DVR
1x1S series balance charging board
1xPropeller disassemble tool
1x VTX系統図

**100g未満 ドローン


Moblite7 1S 650mah Lipo Battery []