F4 1S AIO FC（SPI Rx）は、F411 FC、5A ESC、25mW VTX、SPIレシーバーの4つのコンポーネントを統合しています。 わずか3.92gの超軽量でありながら、驚異的なパフォーマンス機能を維持しているため、1Sブラシレスクワッドでの使用に最適です。

F4 1S AIO FC（No Rx）は、F411 FC、5A ESC、および25mWVTXの3つのコンポーネントを統合します。 TBS Crossfire、Frsky XM +、Spectrum DSMXなどの外部レシーバーをサポートします。一方、このバージョンは2S電源システムを処理できます。


Bullet Point
Integrated with a 25mW VTX, this AIO board(Frsky/Futaba Rx) is ultralight only 3.92g, which can extremely save the weight of building drone, perfectly suitable for the 1S weight-sensitive drone such as Meteor65 HD and HX100 SE.
F4 1S AIO FC(No Rx) not only integrates with the 25mW VTX but also supports a 1-2S power system, which is perfectly suitable for the weight-sensitive drone such as Meteor75 and Beta85 Pro2.
This AIO board also reserves a Plug & Play port for the C01 Camera, C01 Pro Camera and BETAFPV Nano HD Camera, no soldering work needed, super convenient for installation.
Specially added with 2 RGB LED indicators, this board brings the drone an incredible light effect while pilots flying on the night.
This board can handle 5A continuous current(6A burst), supports the 1S lipo battery, brings the drone a stronger flight performance.
Come with a BT2.0 connector, it solves the problem of voltage sag, the discharge can be more efficient, which brings this board a better performance on function for power and responsiveness.


【F4 1S AIO FC(SPI Rx)仕様】
Item: F4 1S AIO FC(Frsky/Futaba Rx)
Weight: 3.92g(without antenna and BT2.0 connector)
VTX Power: 25mW
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Firmware version: betaflight_4.2.0_STM32F411
Receiver: Support Frsky Receiver/ Futaba Receiver
Motor Pin Connecter: 1.25mm Header Pins
Mounting hole size: 29mm x 29mm / suitable for almost all kind of whoop frame

【ESC仕様】
Built-in ESC with 5A continuous and peak 6A current
Input voltage: 1S Lipo
ESC firmware: O_L_5_REV16_8.HEX
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
4 Indicators: Receiver indicator (Blue)/Flight control status indicator (Green)/Flight control power indicator (Red)/VTX indicator (Pink)
Diagram for F4 1S AIO FC(SPI Rx)


SPI Receiver CC2500

Come with the build-in SPI Receiver CC2500, F4 1S AIO FC(SPI Rx) can compatible with Futaba S-FHSS, Frsky D8 and D16 protocol. The default Frksy protocol is Frsky D16, if pilots buy the wrong receiver of the SPI Frsky version or upgrade the wrong firmware accidentally, which needs to switch the protocol to Futaba or FrskyD8, please upgrade the Betaflight Firmware according to this tutorial.



Status LED for F4 1S AIO FC(SPI Rx)
There are 4 LEDs on the bottom of the board to indicate the status, including the Receiver LED ( Blue), FC Status LED(Green), FC Power LED ( Red ) and VTX LED(Pink).



【セット内容】
1x F4 1S AIO Brushless Flight Controller
4x M1.2x4mm Screws
4x M1.4x5mm Screws
4x Anti-vibration Rubber dampers