---

商品の説明

Beta85Xには、GoProヒーロー用のBECボード、ケース、調整可能なマウントが同梱されているため、GoProを使用して簡単に映画を構築でき、重量を大幅に最小限に抑えることができます。 450mah 4sバッテリーで約4分間、素早く安定した飛行が可能です。これは、FPV撮影用のcinewhoopの作成に興味がある人に最適です。

Bullet Point
Beta85X comes with a BEC board, which specially designed for GoPro Hero6. Integrated GoPro stock buttons and LED.
Install customized EOS2 V2 camera and A01 VTX，you can enjoy the real-time FPV feds and low RF interference on flight.
Pad is available for pilot to control the GoPro recording via the radio transmitter.
With the pluggable connector, which is easier to connect with your flight controller for power supply and recording.
Equipped with an adjustable camera mount of 0-50° for FPV film shooting. This will be the best choice for building the smallest cinewhoop drone that can carry a naked GoPro6.

【仕様】
Item: Beta85X for GoPro Hero
Weight: 67.77g (without GoPro Hero or battery)
F4 AIO Brushless FC 12A V2 (BLHeli_S)
Frame: Beta85X Frame V2
Motors: 1105 5000KV Brushless motor
Props: 2" 4-Blades Props
Receiver Option: Frsky XM+ / TBS Crossfire
Camera: Betafpv EOS V2 Camera
Recommended battery: 450mAh 4s 75C battery (Not including)

For providing a great combo for FPV community, we design a BEC board which is for the naked GoPro Hero 6 perfectly. With the carbon fiber case and pluggable connector, it is easier to plug in and out. Meanwhile, we designed the adjustable camera mount of 0-50°, it can be used for the different flying modes of insane flying or slowing flying.

The idea of GoPro Lite
Based on the discussion of the cinewhoop, we designed a BEC board and a fitting case for Naked GoPro Hero 6/7 to make it as a whole GoPro Lite camera. With a pluggable connector and a lightweight of 29g, easier to install on your cinewhoop for FPV filming.

So what is the special of the BEC board? It is integrated with the 5V@2A BEC, the stock GoPro buttons, LED and remote recording, solving the problem of the unstable power supply and redundant FPC connect way. The current BEC board fits for GoPro Hero 6 and Hero 7 Black.

How to Setup Remote Record
Pilot could use the switch on radio transmitter to start/stop record. Some more configuration needed.

For example, if you use F4 FC V2.0 in the drone, like the 95X whoop drone, the connection diagram is shown below. The yellow cable (FC B12 pin pad) is just for the remote record.

We use the Pinio function in Betaflight to control record. First, setup the Pinio function of the B12 pin in the FC board.

resource FLASH_CS 1 NONE
resource PINIO 1 B12
set pinio_box = 40,255,255,255
save

Next, map one of the switch channels in your radio transmitter to this Pinio (aka USER1). As shown below, we map the AUX4 channel in the radio transmitter to USER1 Pinio. The cursor in the orange zone means button released and white zone means pressed. So keep the cursor in the orange zone in default.

Third, check if the Pinio function works. Change the switch and make the cursor move from the orange zone to the white zone, and finally back to the orange zone. Now you could check the LED status to know if the record starts. Use the same process to stop recording.

If you use the 12A F4 AIO FC board, like the 85X whoop drone, you will use the LED_STRIP pin (aka A08 pin pad) for the Pinio function.

resource LED_STRIP 1 NONE
resource PINIO 1 A08
set pinio_box = 40,255,255,255
save

【セット内容】※画像はイメージです。GoProカメラやバッテリーは含まれません。
1x Beta85X for GoPro Hero
1x BEC Board for GoPro Hero
1x Case for GoPro Lite Camera
1x GH1.25 Power Cable (80mm 30AWG)
1x Pack of Screws