---

商品の説明

BETAFPV F4 Brushed Flight Controller V2.0 (SPI FUTABA RX + OSD) [BF-01040009_2 Futaba]

古典的な F4 ブラシ付きフライト コントローラーが、新たな変更と特定の形状を備えて帰ってきました。 ビルトイン CC2500 チップ、デフォルト プロトコルは工場出荷時に Frsky D8 に設定されており、Frsky D16 FCC、Frsky D16 LBT、またはFutaba に調整できます。 さらに、電源ケーブルはPH2.0の代わりにBT2.0コネクタを採用し、性能が向上し、BETAFPV BT2.0シリーズバッテリーと互換性があります。
Specification
CPU: STM32F411CEU6
Six-Axis: MPU6500
ESC: All FETs are rated at 30A maximum
Motor: Support 6x15mm/7x16mm/8x20mm/8.5x20mm etc motors. Recommend BETAFPV 7x16mm Brushed Motors (2CW+2CCW)
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight BETAFPVF411RX 4.2.11
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI Frsky D8 (CC2500 chip, adjustable)
Power Cable: 55mm, with BT2.0 Connector
Weight: 3.68g (with Power Cable)
What's the Upgrade
Compared with the previous version F4 Brushed Flight Controller V1.2, now the V2.0 version comes with SPI Frsky D8 receiver that can be compatible with Futaba S-FHSS, Frsky D16 FCC, and Frsky D16 LBT protocol. The power cable applies BT2.0 connector instead of PH2.0, which solves the problem of voltage sag, and the discharge can be more efficient, bringing this board a better performance on function for power and responsiveness. What's more, with the compatibility of BETAFPV BT2.0 series batteries, it is convenient to upgrade in the future. Besides, it supports custom RGB lights on the Betaflight configuration, which makes your drone unique from others.

Connection diagram for VTX. Here is the example of M03 25-350mW 5.8G VTX

LED status is below.

LED Status Description
Green Flashing Not connected
Green Solid Connected or in bind mode
Red Flashing Disarmed
Red Solid Motor armed
SPI Frsky Receiver
With the build-in SPI Receiver CC2500 chip, F4 Brushed FC V2.0 can be compatible with Futaba S-FHSS, Frsky D16 FCC, and D16 LBT protocol. The default protocol is configured to Frsky D8 out of the factory. Pilots could set up the protocol according to their needs in Betaflight Configurator.

Configuration Protocol
FRSKY_D
Frsky D8
FRSKY_X Frsky D16 FCC
FRSKY_X_LBT Frsky D16 LBT
SFHSS Futaba S-FHSS

RECOMMENDED PARTS LIST
Battery: BT2.0 300mAh 1S Battery
Frame: 65mm Micro Whoop Frame
Props: 31mm 3-Blade
Motors: BETAFPV 7x16mm Brushed Motors (2CW+2CCW)
VTX: M03 25-350mW VTX
Recommend drones: Beta65S BNF Micro Whoop Quadcopter
FAQ
Click here to know SPI Frsky Receiver Binding Manual.
Firmware and Cli Dump file for F4 Brushed Flight Controller.
Note: Please flash Cli Dump file if you flash firmware from Betaflight official site.

Package
1 * F4 Brushed Flight Controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers