---

商品の説明

Cetus X ブラシレス クアドコプターは、2S パワーのフープ ドローンであり、高度な飛行スキルを習得したい初心者に最適です。 より高速で暴力的な飛行のための強力な推進システムを備えており、さまざまなフリースタイルのトリックを実行できます。 M04 400mW VTX および C04 FPV カメラを装備し、より長い無線およびビデオ伝送用に最適化されています。 一方、RC 航空機を構成するための一般的なアプリケーションである Betaflight コンフィギュレーターをサポートしています。



Specification
Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC: F4 1S 12A FC V2.2 (ELRS 2.4G)
Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G/Frsky D8
VTX: M04 25-400mW VTX
Battery: 2*BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins



Improved Video Transmission
Cetus X Brushless Quadcopter comes with M04 25-450mW VTX and C04 FPV camera. M04 25-450mW VTX features a lightweight and adjustable output power for longer distance flying.



Powerful Propulsion System
Equipped with 1103 11000KV Brushless Motor and Gemfan 2020 4-blade props. 1103 motors are designed for 2S quadcopters with incredible power, smooth and quiet operation, and light enough.



Primary Choice for Next Level
Cetus X Brushless Qaducopter Betaflight FC version supports configuring on Betaflight configurator.


Note: Please DO NOT configure ESC or Motor settings on Betaflight configurator.

F4 1S 12A FC V2.2
F4 1S 12A FC board with version V2.2 is first used on Cetus X BNF drone. Here is the specification of the F4 1S 12A FC (ELRS) V2.2.

CPU: STM32F411CEU6 (100MHZ )
Six-Axis: BMI270 (SPI connection)
Firmware version: betaflight_4.3.1_BETAFPVF4SX1280
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI ELRS 2.4G Receiver
Motor Pin Connector: 1.25mm Header Pins
Mounting Hole Size: 26mm x 26mm (suitable for whoop pattern mounting hole)
USB Port: SH1.0 4-Pin
Built-in ESC with 12A continuous and peak 25A current
ESC input voltage: 1S-2S
ESC firmware: C_X_30_REV16_7_20220802.hex for BB51 BLHeli_S hardware
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM

Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer or ICM42688. Please check the below link to download the firmware.

Download the FC firmware betaflight_4.3.1_BETAFPVF4SX1280.hex

Download the newest BLHeliSuite-16714902a here.

Download the BB51 ESC firmware C_X_30_REV16_7_20220802.hex

Note: BetaFlight Configurator, BLHeli Configurator, Bluejay Configurator are invalid for the BB51 ESC now.

Recommended Parts
Radio Transmitter: LiteRadio3, LiteRadio 2 SE
Goggles: VR02 FPV Goggles
Battery: BT2.0 450mAh 1S 30C Battery
Props: Gemfan 2020 4-Blade Propellers
FAQ
ExpressLRS 2.4G is the most popular radio link now. Know more about ExpressLRS here.
Please DO NOT change the ESC or Motor settings on Betaflight configurator, BLHeli Configurator, or Bluejay Configurator, otherwise, the FC will be invalid. Please download and run the latest BLHeliSuite-16714902a for setup.
The frame and props are visible when the camera's angle is 0°. Adjust it to about 25°, then the frame and props are invisible when flying.
Click to download the CLI dump file for Cetus X Brushless Quadcopter.
Click to download the Manual for Cetus X Brushless Quadcopter.
Cetus X Brushless Quadcopter should work with two 1S batteries. Do not recommend using different brand batteries. Highly recommend the original batteries BT2.0 450mAh 1S 30C Battery.
Cetus X Brushless Quadcopter is similar to Meteor85 Brushless Whoop Quadcopter (2S) in many ways. For flying maneuverability and more battery choices, Meteor85 is a good alternative choice.

セット内容：
1 * Cetus X Brushless Quadcopter
1 * BT2.0 Battery Charger and Voltage Tester
2 * BT2.0 450mAh 1S 30C Battery
1 * Phillips Screwdriver
1 * Prop Removal Tool
1 * Type-C Adapter
4 * Gemfan 2020 4-Blades Props
1* VTX系統図
1* 日本語説明書