IFLIGHT ProTek35 4S CineWhoop Analog BNF SFHSS [IF-C009165]

After our very popular 3inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.

Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here...

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it's 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves.

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).

Durable plastic protectors with copper standoffs, portable compact design, easy accessable UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery. Link

Need a naked GoPro case or mount? Checkout our new iFlight naked GoPro Hero8 TPU case to use with your ProTek35. LINK

No Props or frame in view!
High performance True-AIO Board Beast Whoop F7 AIO 45A to save weight and space
T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
Low Resonance frame construction (Less Jello, more Cinematic footage)
Caddx.us Turbo Eos V2 FPVCam 2.1mm 16:9 NTSC
Butter smooth 2203.5 3600KV (4S)
Pre-tuned with smooth freestyle settings


Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

ProTek35 BNF
Board Beast Whoop F7 AIO 45A
Motor: XING 2203.5 3600KV (4S)
Wheelbase: 151mm
Body Size: 118*94.5mmmm
Bottom plate thickness: 3.5mm
Top plate thickness: 2mm
Top and bottom plate spacing: 20mm (aluminum standoff height)
Propeller size: 3.5 inch
FC pattern: 25.5*25.5mm / 20*20mmmm
FPV cam spacing: 20mm
Weight: 305g (without battery)

FC // Beast F7 AIO
Gyro: MPU6000
Blackbox: 8Mb Onboard Flash
BEC output: 5V 2.5A
Barometer: BMP280
Connector: Micro-USB
OSD: AT7456E
FC Firmware:IFLIGHT_F745_AIO
Mounting pattern: 25.5*25.5mm φ3mm
Dimensions: 32.5*32.5mm
Weight: 8.5g

ESC // 45A 2-6S
Uarts: 5
Current Sensor: Yes
Input: 2-6S LIPO
Current scale: 200
Constant: 45A / Burst: 50A
BLHeli: BLHeli-S
Telemetry: no
ESC Firmware: BlheliS G-H-30
Mounting pattern: 25.5*25.5mm/Φ3mm
Dimensions: 32.5*32.5mm

VTX// 5.8GHz SucceX Micro 300mW VTX
Power: PIT/25/100/200mW/300mW
Antenna interface: IPEX (UFL)
VTX protocol : IRC Tramp
Size: 13.5x14.5mm
Weight: 1.4g
Size Extender (stackable adapter):
Mini VTX size: 20x20mm, 2mm hole, total weight (incl. VTX): 3.4g
Whoop VTX size: 16mm/25mm, 2mm hole, total weight (incl. VTX): 2.9g

4S 95C 1300mAh (別売り)

ProTek35 4S CineWhoop Analog BNF
1x AC2000(RX)
1x ProTek35 Frame
1x Caddx.us Turbo Eos V2 FPVCam
1x Albatross LHCP 5.8g antenna
2x TPU camera side plate soft mount
2x Nazgul 3535 propeller (Set of 4 - 色は画像と異なる場合があります)
1x iFlight Lipo Strap 15*150mm (色は画像と異なる場合があります)
1x iFlight Lipo Strap 15*250mm (色は画像と異なる場合があります)
1x GoPro TPU bottom stand black (GoPro Protector not included)
1x 日本語簡易説明書
1x 系統図
こちらの受信機は、FUTABA S-FHSSとFRSKY D16を切り替えることによって両方のシステムをご使用頂けます。

2. バインドボタンを爪楊枝などを使って長押しする(5〜10秒くらい)。長押ししている間一瞬ライトが光り、その後点灯すれば切り替え成功です。