BETAFPV F4 1S AIO Brushless Flight Controller NO RX [BF-00313785_4]

F4 1S AIO FC(SPI Rx)は、F411 FC、5A ESC、25mW VTX、SPIレシーバーの4つのコンポーネントを統合しています。 わずか3.92gの超軽量でありながら、驚異的なパフォーマンス機能を維持しているため、1Sブラシレスクワッドでの使用に最適です。

F4 1S AIO FC(No Rx)は、F411 FC、5A ESC、および25mWVTXの3つのコンポーネントを統合します。 TBS Crossfire、Frsky XM +、Spectrum DSMXなどの外部レシーバーをサポートします。一方、このバージョンは2S電源システムを処理できます。

Bullet Point
Integrated with a 25mW VTX, this AIO board(Frsky/Futaba Rx) is ultralight only 3.92g, which can extremely save the weight of building drone, perfectly suitable for the 1S weight-sensitive drone such as Meteor65 HD and HX100 SE.
F4 1S AIO FC(No Rx) not only integrates with the 25mW VTX but also supports a 1-2S power system, which is perfectly suitable for the weight-sensitive drone such as Meteor75 and Beta85 Pro2.
This AIO board also reserves a Plug & Play port for the C01 Camera, C01 Pro Camera and BETAFPV Nano HD Camera, no soldering work needed, super convenient for installation.
Specially added with 2 RGB LED indicators, this board brings the drone an incredible light effect while pilots flying on the night.
This board can handle 5A continuous current(6A burst), supports the 1S lipo battery, brings the drone a stronger flight performance.
Come with a BT2.0 connector, it solves the problem of voltage sag, the discharge can be more efficient, which brings this board a better performance on function for power and responsiveness.

【F4 1S AIO FC(NoRx)仕様】
Specification of F4 1S AIO FC(No Rx)
Item: F4 1S AIO FC(No Rx)
Weight: 3.83g (without antenna and BT2.0 connector)
VTX Power: 25mW
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU6000 (SPI connection)
Firmware version: betaflight_4.2.0_STM32F411
Receiver: Support External Receiver, SPI Receiver, including Frsky XM/XM+ receiver, Futaba receiver, Crossfire receiver and DSMX receiver
Motor Pin Connecter: 1.25mm Header Pins
Mounting hole size: 29mm x 29mm / suitable for almost all kind of whoop frame

Built-in ESC with 5A continuous and peak 6A current
Input voltage: 1S Lipo
Input voltage: 1-2S Lipo
ESC firmware: S_H_70_REV16_7.HEX
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
4 Indicators: Receiver indicator (Green)/Flight control status indicator (Blue)/Flight control power indicator (Red)/VTX indicator (Pink)
Diagram for F4 1S AIO FC(No Rx)

How to Connect the External Rx to the FC(No Rx)
For more convenience to the pilots, we specially design the Plug & Play SPI Frsky Rx for the F4 1S AIO FC(No Rx), no soldering work needed, super easy to install.

Status LED for F4 1S AIO FC(No Rx)
There are 4 LEDs on the bottom of the board to indicate the status, including the Receiver LED ( Blue), FC Status LED(Green), FC Power LED ( Red ) and VTX LED(Pink).

1x F4 1S AIO Brushless Flight Controller
4x M1.2x4mm Screws
4x M1.4x5mm Screws
4x Anti-vibration Rubber dampers

おすすめパーツ F4 1S AIO FC(No Rx)※別売り
Battery: BT2.0 300mAh 1S Battery / BT2.0 450mAh 1S Battery / BT2.0 260mAh 1S Battery/ BT2.0 300mah 2S Battery
Frame: Meteor65 Frame / Meteor75 Frame / Beta85 Pro2 Frame
Props: 31mm 4-Blades props / 40mm 4-blades props / Gemfan 2020 4-Blades Props
Motors: 0603 motors / 0703 motors / 0802 motors / 0802SE 22000KV Motor / 1103 11000KV motors / 1102 18000KV motor
Camera: C01 Camera / C01 Pro Camera / BETAFPV Nano HD Camera