Beta85X HD Whoop Quadcopter (4S) - HD DVR, SFHSS RX [BF-313489_4]

Beta85X pushes the new era of brushless whoop drones to a higher level. With the new power system, you could fly real acro even with HD camera on 4S power.
With the high performance STM32F051 processor FC boards and tuned Betaflight OMNIBUSF4SD (OBSD) , faster input signals with lower latency and higher update rate are reachable, give you much more power.
Comes with upgraded F4 V2 4S FC, this FC is equipped with ports which support to plug the receiver, ESC, led board and VTX directly, no need to solder, convenient for installation.
Durable and light enough frame is customized for the Beta85X. To increase its stability, we specially add an extra stiffener brace of carbon fiber. Whole drone no soldering or tinkering necessary.
Upgraded 1105 motor from 6000KV to 5000KV, with a light weight but definitely will give you extreme power and speed to support 4S. Motor comes with cable connectors. Just plug and play. EMAX Avan 2" prop is the best combo in this Beta85X drone.
450mAh 4S high rate battery is recommended by default. But pilot could also use their own batteries with battery strap. Optional and affordable.

Weight: 78g (without battery)
F4 V2 4S Flight Controller
16A BLHeli_32 ESC
Motors: 1105 5000KV with connector
Props: EMAX Avan 2" 4-Blades Props
FPV Camera: Customized EOS2 Camera
FPV Canopy: Canopy for EOS2 Camera
Receiver Option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky / TBS Crossfire
Battery: 4S 450mAh Battery (Not including)
5.8G FPV antenna
Beta85X Frame Kit
Carbon Fiber Stiffener Brace for Beta85X Frame
Battery strap fits for micro 2S-4S battery
Flight time: 4min - 6min with 450mAh 4S battery (smooth flight in a windless environment)

CPU: STM32F405
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD(OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)

Support BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
MCU: STM32F051K66

HD Camera and Z02 VTX
The primary purpose of the Beta85X drone is for a cinematic whoop drone. Many polits revamp their Beta75X to HD whoop drone--They add a HD DVR camera on Beta75X drone to get high defination and beautiful flying footage and video. Inspired by this, we want to provide a BNF whoop drone with HD DVR camera by default so that pilot do not need to assemble it by hand and also get more power on punch for acro mode.

Output power: 25mW and 200mW (Adjustable)
Smart Audio function is included for radio control
Antenna: Customized ZRC antenna
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Caddx Turtle V2 Camera
TV System: NTSC
Field of view: 100-120 degrees with 1/3 lens

Inspirations by YKS' footage with Beta75X.
Now the Beta85X HD version is here !!!

now more about cine whoop from NURK FPV's blog.

In the Beta85X design, the part of HD DVR is independent of the drone. You could mount or remove the HD DVR part very easy. In default, the drone comes with CADDX Turtle V2 HD camera.

The canopy for HD DVR camera is 3d printing with SLA, which is compatible with Runcam Split Mini 2.

Download the STL File for the HD camera mount.

This Beta85X has upgraded in every individual parts likd FC, ESC, Motor, etc. Which can suport 4S power with a steady performance and bring you into a glorious FPV world.

F4 V2 FC
Extra 4 pluggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting.

16A BLHeli_32 ESC
Support 4S Power. Written for ESC's that utilize 32-bit MCU. With the increase in processing power, faster input signals with lower latency and higher update rate would be possible in BLHeli_32, such as Dshot1200!
Using single N-channel MosFETs on ESC board, which has a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
Current sensor included.

Soldering with 25V/220uf electrolytic capacitor, for reducing the defective rate caused by the instantaneous high voltage.

1105 5000KV Motor
Lower 5000KV for new Beta85X 4S, which could support 4S power which won't cause the issue of overheat or burn (maybe the ESC).

We DO NOT recommend the 1105 6000KV motors for 4S power because the motor may overheat or burn which will cause permanently damage on the motor or ESC. And don't use 1105 5000KV motors for 3S power, the performance will not be as good as the 1105 6000KV motors since lack of power.

Beta85X Frame

The Stiffener Brace of Carbon Fiber can reinforce the Beta85X frame, avoid unstability caused by too strong power when Beta85x is flying.
Extra screws holes to fix the ESC, can prevent ESC from loosening and solve the adverse wear and tear reaction from ESC and FC caused by vibration.

The Beta85X drone also comes with "props out" by default. Why we need "props out" direction?

Default Betaflight props direction, quadcopter dips and "washes out" in hard corners. With reversed props or "props out", no more dipping even in hardest cornering.

1x Beta85X BNF 4S Whoop Quadcopter (HD DVR, SFHSS RX)
1x OSD Menu Board
1x 系統図

こちらの受信機は、FUTABA S-FHSSとFRSKY D16を切り替えることによって両方のシステムをご使用頂けます。




Props: 2" 4-Blades Props
EMAX 2035 Avan 2'' 4-Blade Propellers (1.5mm Shaft)
AVAN 2035 4-blade Whoop Propellers 2ペア
2x3.5" 2035-4S (50.8mm) T-Type Bullnose Quad Propeller
2x3.5" 2035-4S (50.8mm) T-Type Bullnose Propeller

F405 V2 Flight Controller and 16A BLHeli_32 ESC(コンボ)

BETAFPV 1105 5000KV Brushless Motors [BF-00313530]

Caddx Turtle V2 1080p 60fps Mini HD FPV Camera w/ DVR (FOV 155° / Red)[09-574]
Caddx Turtle V2 1080p 60fps Mini HD FPV Camera w/ DVR (FOV 155° / Black) [09-573]

BETAFPV Canopy for Beta85X HD [BF-00313513]

Futaba S-FHSS / Frsky,D16

Beta85X 4S 4K Frame Kit (Upgrade)

A01 25-200mW 5.8G VTX

BETAFPV LED Board (2PCS)[BF-00313443]

TATTU 450mAh 14.8V 75C 4S1P Lipo Battery Pack Long
Tattu 450mAh 11.1V 75C 3S1P Lipo Battery Pack

KW:CineWhoop KW:Tinywhoop KW:85X-4S